Product Overview
Genuine Velcro Brand Hook and Loop Strip Pair, Adhesive Backed, 5/8 Inch Wide by 7-1/2 Inches Long
Condition
New. One unit here is one matched pair: a hook strip and a loop strip, each 5/8 in wide by 7-1/2 in long. Both strips are cut clean at the ends, the black fabric faces are full and uncrushed with no flattened nap, and the pressure sensitive adhesive on each is still sealed under its factory paper release liner, which is printed edge to edge with the repeating red Velcro wordmark. Our photographs show both halves of the pair, the stiffer hooked strip and the softer looped strip, with the liners intact on the back. No dust, no curl, no yellowing on the liner.
Same or next business day shipping from our Idaho warehouse. Honest pricing, no nonsense.
Online since 1999. We are here for our customers, with a no-hassle satisfaction guarantee.
Product Overview
This is a Genuine Velcro Brand linear fabric fastener, manufacturer number 90438blk, supplied as a hook-plus-loop pair: one hook strip and one loop strip, each measuring 0.625 in / 15.875 mm wide by 7.5 in / 190.5 mm long in black. That is the whole fastener in one buy, with no second half to source. Hook and loop works the way it always has: a field of small stiff hooks catches a mat of soft loops, so the joint closes with hand pressure, peels open without tools, and re-closes as many times as the job asks. Both strips carry a pressure sensitive adhesive under a paper release liner, so mounting is peel and press with no drilling, no screws, and nothing to mix or cure. Adhesive chemistry, temperature range, shelf life, and cycle life are not stated in our records for this piece - Not confirmed, verify against the Velcro datasheet before use in high heat, outdoor exposure, or any load-bearing or safety-critical mount.
Key Features
- Brand: Genuine Velcro Brand, manufacturer number 90438blk
- Contents: one matched pair - one hook strip and one loop strip
- Width: 0.625 in / 15.875 mm, each strip
- Length: 7.5 in / 190.5 mm, each strip
- Material: black woven hook and loop fabric
- Backing: pressure sensitive adhesive on both strips, factory release liners still in place
- Liner: paper, printed with the red Velcro wordmark
- Condition: New
- Trims shorter with ordinary scissors
- Adhesive type, temperature rating, and cycle life: Not confirmed - verify against the Velcro datasheet before use
Applications
- Bench technician dressing a wiring harness inside an equipment cabinet where drilling another hole is not an option
- Audio or AV installer mounting a wireless receiver pack to a rack panel so it lifts off for battery swaps
- Prototype builder holding a battery, sensor board, or controller to a chassis while the layout is still changing
- Shop owner fixing a removable label, access cover, or light dust panel that has to come off at every service interval
Frequently Asked Questions
What exactly do I get for one?
One matched pair: one hook strip and one loop strip, each 5/8 in wide and 7-1/2 in long, each with its own pressure sensitive adhesive under a factory liner. Stick the hook half to one surface, the loop half to the other, and the fastener is complete. There is no second half to order.
Is this actual Velcro Brand material or a generic hook and loop?
Genuine Velcro Brand. The release liners are printed with the repeating red Velcro wordmark, clearly legible in the close-up photo, and the pair carries manufacturer number 90438blk.
What are the exact dimensions?
Each strip in the pair is 0.625 in / 15.875 mm wide by 7.5 in / 190.5 mm long. Those are the manufacturer figures for 90438blk; we have not re-measured this piece against a rule. If your run is shorter, ordinary scissors will trim both halves without fraying the edge badly.
Is the adhesive still sealed?
Yes, on both strips. The factory release liners are on the back in every photo, so the adhesive has never been exposed. We have not peel-tested it and we have no shelf-life or temperature figures on file for this lot. Clean and dry the surface before you press it down, and for heat, outdoor, or load-bearing use, verify against the Velcro datasheet first.
Will it stick to a painted or textured surface?
Not confirmed for your surface. Pressure sensitive adhesive holds best on clean, smooth, dry, non-porous material such as sheet metal, glass, smooth plastic, or a finished panel. On rough powder coat, bare wood, or anything oily or dusty, plan on a mechanical fastener or surface prep instead.
Why buy two or three pairs here instead of a bulk roll or a big-box multipack?
Because most jobs need a few fasteners, not twenty-five yards of hook and twenty-five yards of loop. These are stocked as ready-to-use pre-cut pairs and you pick the count: one pair for a single harness, a handful for a rack build, a few more for the parts drawer. No forced pack of 10 or 50, no half-used roll curling up in a bin for the next six years. Shipping is $8 flat rate and free once your order passes $28, and orders leave our Idaho warehouse the same or next business day.
Hook and loop began with burdock burrs stuck to a Swiss engineer's dog, and decades on it is still the fastest way to mount something you already know you will have to take back off. Peel the liners, press them down, get on with the build.
